Inline blending takes the guesswork out of plant-based beverages

Inline continuous blending has already shown it can revolutionize the standardization of fat, protein and sugar (Brix) in dairy, cheese and beverage production. Here’s why we think it’s an even bigger game-changer for plant-based beverages.

Table with five bowls filed with plant-based ingredients

Plant-based ingredients can vary in their levels of carbohydrate, fat, protein, and other essential components, which can lead to greater variance in product quality. For example, a slurry with a variable fat or total solids (TS) content challenges you to adapt the blend to meet fat or TS declarations.

Batch blending requires operators to spend a lot of time checking quality parameters. They have to sample the batch frequently, walk the sample to the quality lab to measure it, and if the measurements are not within recipe limits, they have to recalculate how much ingredient to add, then wait for a homogenous blend in order to take another sample. All this takes time and leaves the process open to operator error. This is one of the reasons a batch process is often not as accurate (close to the target level) or precise (consistent) as a metered inline process.

Greater yield, higher quality

But with inline blending, sensing and feeding controls provide automatic adjustments to meet the quality parameters of the recipe, boosting both accuracy and precision. Automated recipe control minimizes operator error because it reduces the number of operator decisions. The improved recipe control translates into more consistent product quality – and huge savings.

Inline blending helps cut wastage of premium or hard-to-handle ingredients. For example, the base ingredients can be blended first, and then the expensive ingredients can be fed and metered into the main line to match quality parameters. High precision, increased yield and our guarantees mean more finished product can be produced from the same volume of raw ingredients. Typically, we see a 1% increase in yield with inline blending.

Huge savings from tanking down and cleaning less

Clever coordination between the blender and UHT system means we can eliminate waste on start-up, and production can be run until the premium ingredient is finished. Other ingredients can be pushed back into their supply tanks. No mix phase equals minimal waste.

Moreover, inline blending minimizes the volume of product that is likely to degrade. The end result? Higher product yield and less giveaway of expensive ingredients.

Inline blending requires fewer tanks to produce the same amount of product per day, and since they are smaller, they have smaller footprints and can be housed in smaller buildings. This enables starting up with a lower investment cost.

“Inline blending streamlines production for plant-based beverages,” says Helen Sellar, Product Manager for Liquid Foods at Tetra Pak Processing Systems. “In fact, we believe so strongly in the operational efficiency results we have seen, that we offer performance guarantees for total solids in our inline blending solutions.”

Reduced energy and water consumption

The environmental bonuses stem from less product waste, lower energy consumption and less cleaning chemicals. This puts less load on the sewage system, less equipment and piping, lower water and detergent consumption – in fact, lower resource usage overall. Even processing and reprocessing waste will cost less. With lower waste, a higher yield, and a heavily reduced need for CIP, use of inline blending can do marvels for your sustainability targets.
Further supporting the environment benefits, inline blending also reduces the number of areas that are exposed to microbiologically active oat base, making cleaning easier.
Batch tanks with final product are cleaned frequently. So, with fewer and smaller tanks to clean in continuous production, that don’t have final product, we find that CIP costs (water, chemicals, energy) fall greatly because the number of CIP cycles can be cut by more than 50%.
Tetra Pak has a large installed base of inline blending solutions in a number of application areas and has several decades of experience in plant-based processing – and building cutting-edge technology that keeps it going. You can rely on us to guide you to an optimized production process

Inline – a paradigm shift in blending

In beverage production, blending of liquid ingredients can be done in a batch tank, much as it has been done for decades. And this is fine for small batches up to 5,000 litres. But modern inline blending enables a larger-scale continuous process, permitting much more efficient and consistent production. 

Inline or continuous blending combines several different liquid streams into a single large stream. This represents a paradigm shift over batch blending because it requires fewer and smaller tanks. Both the ingredients and the resulting blended product can also be measured more precisely and efficiently with automated instrumentation. 

Package with oat drink

Converting production for oat wave success

Liquid food producers should weigh the pros and cons of converting or investing in a new line before expanding into oat-based beverages.

Oat-based beverage

Processing core technologies for intelligent customization

Oat-based beverages are winning increased popularity. As a useful starting point for producers entering this segment, we have identified the main challenges

Food experts

Behind the beverage: Meet oat drink experts

It takes a committed team of professionals — including food scientists, technologists, strategists and engineers — to bring oat-based beverages to market.